1. I beg your pardon dynamic routing protocol was arisen to interconnect various Internet company providers?
2. Which routing protocol is restricted to smaller sized network implementations since it does no accommodate expansion for bigger networks?
3. What two work do dynamic routing protocols perform? (Choose two.)
update and also maintain routing tables*
propagate host default gateways
assign IP addressing
4. When would it be an ext beneficial to use a dynamic routing protocol instead of revolution routing?
in an company with a smaller network that is not intended to grow in size
on a stub network that has a single exit point
in an organization where routers endure from performance issues
on a network where there is a most topology changes*
5. As soon as would that be more beneficial to usage static routing rather of dynamic routing protocols?
on a network where dynamic updates would pose a protection risk*
on a network the is meant to continually thrive in size
on a network that has a big amount of redundancy paths
on a network that frequently experiences attach failures
6. What is a objective of the network command as soon as configuring RIPv2 as the routing protocol?
It identify the interfaces the belong to a stated network.*
It mentions the remote network that deserve to now be reached.
You are watching: Which dynamic routing protocol was developed to interconnect different internet service providers?
It immediately advertises the stated network come neighbor routers v a classful mask.
It populates the routing table v the network entry.
7. A network administrator configures a static route on the sheet router the a network to entrust a gateway of last resort. Just how would a network administrator configure the edge router to instantly share this path within RIP?
Use the auto-summary command.
Use the passive-interface command.
Use the network command.
Use the default-information originate command.*
8. What is the function of the passive-interface command?
allows a routing protocol to front updates the end an user interface that is absent its IP address
allows a router come send routing to update on one interface yet not get updates via the interface
allows an interface to remain up there is no receiving keepalives
allows interfaces come share IP addresses
allows a router to obtain routing to update on an interface yet not send to update via that interface*
9. Which path would be immediately created once a router user interface is activated and also configured v an IP address?
D 10.16.0.0/24 <90/3256> via 192.168.6.9
C 192.168.0.0/24 is directly connected, FastEthernet 0/0*
S 192.168.1.0/24 is straight connected, FastEthernet 0/1
O 172.16.0.0/16 <110/65> via 192.168.5.1
10. Refer to the exhibit. I m sorry two species of routes might be used to define the 192.168.200.0/30 route? (Choose two.)
level 1 parental route
level 1 network route
level 2 kid route*
11. What occurs next in the router lookup process after a router identifies a location IP address and locates a equivalent level 1 parent route?
The level 2 child paths are examined.*
The level 1 supernet routes are examined.
The level 1 ultimate courses are examined.
The router autumn the packet.
12. Which course would be supplied to forward a packet v a source IP attend to of 192.168.10.1 and a location IP resolve of 10.1.1.1?
C 192.168.10.0/30 is straight connected, GigabitEthernet0/1
S 10.1.0.0/16 is directly connected, GigabitEthernet0/0
O 10.1.1.0/24 <110/65> via 192.168.200.2, 00:01:20, Serial0/1/0*
S* 0.0.0.0/0 <1/0> via 172.16.1.1
13. I beg your pardon two requirements are offered to identify if a route can be taken into consideration as an ultimate route in a router’s routing table? (Choose two.)
be a default route
contain an exit interface*
be a classful network entry
contain a next-hop IP address*
14. What is a disadvantage of utilizing dynamic routing protocols?
They room only suitable for simple topologies.
Their configuration intricacy increases as the dimension of the network grows.
They send messages around network status insecurely across networks by default.*
They require administrator treatment when the pathway of website traffic changes.
15. Which 2 statements are true regarding classless routing protocols? (Choose two.)
sends subnet mask info in routing updates*
sends finish routing table upgrade to every neighbors
is sustained by RIP variation 1
allows for use of both 192.168.1.0/30 and also 192.168.1.16/28 subnets in the exact same topology*
reduces the lot of address an are available in one organization
16. Refer to the exhibit. Based on the partial calculation from the display ip path command, what two facts can be determined around the RIP routing protocol? (Choose two.)
RIP version 2 is running on this router and its RIP neighbor.*
The metric come the network 172.16.0.0 is 120.
RIP version 1 is to run on this router and also its RIP neighbor.
The command no auto-summary has been offered on the RIP neighborhood router.*
RIP will advertise 2 networks come its neighbor.
17. When configuring RIPv2 ~ above an companies network, an technician enters the command network 192.168.10.0 into router construction mode.
What is the an outcome of start this command?
The interface of the 192.168.10.0 network is sending version 1 and also version 2 updates.
The user interface of the 192.168.10.0 network is receiving version 1 and version 2 updates.
The user interface of the 192.168.10.0 network is sending only version 2 updates.*
The user interface of the 192.168.10.0 network is sending RIP hello messages.
18. A destination route in the routing table is suggested with a code D. Which kind of course entry is this?
a static route
a route offered as the default gateway
a network directly connected to a router interface
a route dynamically learned with the EIGRP routing protocol*
19. Describe the exhibit. Which user interface will it is in the exit interface to front a data packet v the destination IP resolve 172.16.0.66?
20. Which type of path will need a router to do a recursive lookup?
an ultimate course that is using a next hop IP address on a router that is not using CEF*
a level 2 child course that is utilizing an departure interface on a router that is not using CEF
a level 1 network route that is making use of a next hop IP attend to on a router the is using CEF
a parent route on a router the is making use of CEF
21. Which route is the finest match because that a packet entering a router with a destination address of 10.16.0.2?
S 10.0.0.0/8 <1/0> via 192.168.0.2
S 10.16.0.0/24 <1/0> via 192.168.0.9*
S 10.16.0.0/16 is straight connected, Ethernet 0/1
S 10.0.0.0/16 is directly connected, Ethernet 0/0
22. A router is configured to get involved in multiple routing protocol: RIP, EIGRP, and also OSPF. The router must send a packet to network 192.168.14.0. Which course will be used to forward the traffic?
a 192.168.14.0/26 route that is learned via RIP*
a 192.168.14.0/24 route that is learned via EIGRP
a 192.168.14.0/25 path that is learned via OSPF
a 192.168.14.0/25 course that is learned via RIP
23. What is different in between IPv6 routing table entries compared to IPv4 routing table entries?
IPv6 routing tables include local route entries which IPv4 routing tables do not.
By architecture IPv6 is classless for this reason all routes are properly level 1 can be fried routes.*
The selection of IPv6 courses is based upon the shortest matching prefix, unequal IPv4 route an option which is based on the longest corresponding prefix.
See more: Calories In Red Leaf Lettuce, Red Leaf, Raw, Carbs In Red Leaf Lettuce
IPv6 does not use static routes to populate the routing table as offered in IPv4.
24. Match the dynamic routing protocol ingredient to the characteristic. (Not all alternatives are used.)
data structurestables or databases that room stored in RAM
routing protocol messagesexchanges routing information and maintains accurate information around networks
algorithma finite perform of procedures used to recognize the finest path
25. Complement the characteristic come the corresponding type of routing. (Not all choices are used.)
Place the options in the following order: <+> commonly used top top stub networks <+> less routing overhead <#> brand-new networks are included automatically to the routing table <#> best choice for large networks